The best coating effects of our HairCoat(s) can be accomplished after HEAT-DRYING.)

The best way for drying the WET HAIR (after) treated with our Hair Coat is ;
(1) have the HAIR (after HairCoat-treatment) spin-dried for about 6 minutes with a washing machine
just like CW466-H in your house for family use in order to get rid of about 80% of water (wet-feeling but nothing
dropping) from the HAIR treated & wetted with HairCoat-solution, (2) and, have the HAIR placed on a tray with
many small holes 5 mm in diameter, 5 mm far from each hole), and give very warm heat, about 80 degree C.
for a least 90 minutes or more in case the hair amount is a few kgs or less.

	@@/ If you have the haircoat-treated hair not spin-dried before putting into an oven, you can have better or worse coating effect because more haircoat will remain on the cuticle (surface) of the hair.
	@@/ I would suggest you do  spin drying using a spin dryer (CW466-H) in case you process 1 bundle of hair  (100 gr / dozens or hundreds of hair strands) tied with a rubber band, please do SPIN DRYING 2 times having(keeping) the location of the rubber band changed (moved) each time. Otherwise, the HairCoat solution (water & HairCoat) of the hair strands under the rubber band will not be removed enough, and there can be residue (HairCoat deposit, scum) remaining between hairs, specially around the place tied by a rubber band.
In case the hair is not spin-dried, the drying time should be over 4 hours in case of a few kgs of hair, or more than 7 hours in case dozens of hair is to be dried in an oven (drying machine). You can use a room in your house (for example) as a drying room. and prepare(use) something just like A MOSQUITO NET in metal and a stove (heater). In that case, you should have the window a little bit open, 1 cm (?) so that moisture or water on the hair can vaporize away through the opening. Otherwise, the hair will be not dried, or will be steamed. In case you do not have any spin-dryer or a washing machine used in your house, just take hair from HairCoat-solution (mixture) squeezing out the solution from the hair, and place the hair on a mosquito net or on a metal tray with holes or hang the hair clothesline to dry in the shade in well ventilated place. @@: I would suggest you do  spin drying using a spin dryer (CW466-H) in case you treat 1 bundle of hair  (100 gr / dozens or hundreds of hair strands) tied with a rubber and, please do SPIN DRYING 2 times , having(keeping) the location of the rubber band changed (moved) each time. Otherwise, the HairCoat solution (water & HairCoat) of the hair strands under the rubber band will not be removed enough, and there can be residue (HairCoat deposit, scum) remaining between hairs, specially around the place tied by a rubber band. Of course, there can be the case you can have better effect or result without spin drying. Just have tests 2 ways, with and without spin drying.

OTHERWISE, HAIR WILL BE STEAMED OR BOILED, NOT DRIED.

MEANWHILE, WHEN YOU DRY SYNTHETIC FIBER-PIECES AFTER APPLYING
THE HAIRCOAT CW7892-FR-GN(General fiber) or CW78899-FR-HR(Heat Resistant fiber), PLEASE USE HEAT ( if you can use an oven, or heat for drying) AT AROUND 40 ~ 50 DEGREE C.

SOME OF SYNTHETIC FIBERS CAN BE CHANGED IN QUALITY AT 70, 80, OR 90 DEGREES C.

YOU SHOULD HAVE TESTS ON THE FIBER OF YOUR WIGS OR HAIR EXTENSIONS BEFORE YOU USE HIGH TEMPERATURE OF HEAT FOR DRYING.

OF COURSE, IF YOU CAN BE SURE THE FIBER OF YOUR WIGS OR HAIR EXTENSIONS ARE MADE OF HEAT RESISTANT FIBER, YOU CAN USE 80 DEGREE C OF HOT AIR OR HEAT.